Products with Xilinx FPGA

TE0711 Xilinx Artix-7:35T｜High IO Xilinx Artix-7 35T Module with speedgrade 2C and USB

The Trenz Electronic TE0711-01-35-2C is a FPGA module integrating a Xilinx Artix-7 35T, 32 MByte Quad SPI Flash memory for configuration and operation, and powerful switch-mode power supplies for all on-board voltages. A large number of configurable I/O's is provided via rugged high-speed stacking strips.

• Key Features

  • Xilinx Artix-7 XC7A35T-2CSG324C
  • Rugged for shock and high vibration
  • 32 MByte QSPI Flash memory
  • 100 MHz MEMS oscillator
  • Plug-on module with 2 x 100-pin and 1 x 60-pin Razor Beam High-Speed hermaphroditic Terminal/Socket Strips (regular 4 mm)
  • 178 FPGA I/O's (84 differential pairs) available on board-to-board connectors
  • On-board high-efficiency DC-DC converters
    • 4.0 A x 1.0 V power rail
    • 1.0 A x 1.8 V power rail
    • 1.0 A x 1.5 V power rail
  • System management and power sequencing
  • eFUSE bit-stream encryption
  • AES bit-stream encryption
  • Four LEDs (three  freely used by user design, one system controller CPLD status LED)
  • FTDI FT2232H USB 2.0 High Speed to UART/FIFO
  • Evenly-spread supply pins for good signal integrity

Scope of Delivery

• 1 x TE0711-01-35-2C Trenz Electronic 4 x 5 cm  FPGA module with Xilinx Artix-7 35T
• 8 x screws
• 4 x bolts

TE0865 Xilinx UltraScale+ Series- ZU11-Xilinx Zynq UltraScale+, SDRAM on PS and PL, Flash, Ethernet, USB(ZU11, ZU17, ZU19)

The Trenz Electronic TE0865 Series is a high-performance MPSoC module integrating a Xilinx Zynq UltraScale+ ZU11 / ZU17 / ZU19, 4 GByte DDR4 SDRAM with ECC on PS, 4 GByte DDR4 SDRAM on PL, 256 MByte Flash memory for configuration and operation, Gigabit Ethernet PHY, and powerful switch-mode power supplies for all on-board voltages. A large number of configurable I/O's is provided via rugged high-speed stacking connections. 

Key Features

• Xilinx Zynq UltraScale+ Series
• ZU11EG, C1760 Pin Packages
• Rugged for shock and high vibration
• Graphics Processing Unit (GPU): Mali-400 MP2
• Plug-on module with 4 x Samtec ADM6 board to board connectors
• 4 GByte (64-bit) DDR4 SDRAM with ECC on PS
• 4 GByte (64-bit) DDR4 SDRAM on PL
• 256 MByte QSPI boot Flash
• 8 GByte e.MMC
• 1 x Gigabit Ethernet transceiver PHY
• USB2.0 PHY
• Total I/O: 370
• Gigabit transceivers: 32 x GTH, 16 x GTY, 4 x GTR
• EEPROM with MAC
• System controller (Intel MAX 10)
• All power supplies on board, 12V single supply
• Evenly spread supply pins for good signal integrity
• Dimensions: 7.5 x 10 cm form factor

Scope of Delivery

• 1 x TE0865-02-ABI21MA Trenz Electronic MPSoC module with Xilinx Zynq UltraScale+ ZU11EG

TE0890-S7 Mini｜Fully Open-Source Module with Xilinx Spartan-7 7S25, 64 Mbit HyperRAM

The Trenz Electronic TE0890-01-P1C-5-A is a FPGA module integrating a Xilinx Spartan-7, 64 Mbit HyperRAM DRAM (may be used as video frame buffer), 64 Mbit Config PROM for dual-boot and/or SW code storage and dual-pinout DIP-40 or 50mil 80 pin connectors for 32 or 64 FPGA 3.3V I/Os

The module is footprint compatible with 7S6, 7S15, 7S50 FTGB-196 devices.

Key Features

• Xilinx Spartan-7 XC7S25-1FTGB196C FPGA
• Dimensions: 2.7 x 5.2 cm
• Fully Open-Source Spartan-7 Module
• 7S25 target with 23K logic cells, 29K flops, 45 36Kb BRAMs, 80 mults.
• Footprint compatible with 7S6, 7S15, 7S50 FTGB-196 devices
• Devices fully supported by free "Web Pack" Vivado for Synthesis, Place + Route
• Dual-pinout DIP-40 or 50mil 80 pin connectors for 32 or 64 FPGA 3.3V I/Os
• 64 Mbit Config PROM for dual-boot and/or SW code storage
• 64 Mbit HyperRAM DRAM (may be used as video frame buffer)
• Standard 1x6 FTDI cable serial interface to Host-PCs
• Standard 1x6 Digilent HS2 JTAG header for initial PROM programming
• 5V supply input (4.0V-5.5V per PAM2305 spec)

Scope of Delivery

• 1 x TE0890-01-P1C-5-A Trenz Electronic FPGA module with Xilinx Spartan-7 

TE0716 - SoM with Xilinx Zynq-7000 SoC XC7Z020, 1 GByte DDR3L, 45 x 65 mm

The Trenz Electronic TE0716 is a commercial-grade* SoM (System on Module) based on Xilinx Zynq-7000 SoC XC7Z020*, with 1 GByte of DDR3L-1600 SDRAM*, 32 MByte of SPI Flash memory, 10 x 12-Bit Low Power SAR ADCs, 512 Kb serial EEPROM, Gigabit Ethernet PHY transceiver, an USB PHY transceiver, a single chip USB2.0 to UART/JTAG interface (Xilinx license included), and powerful switching-mode power supplies for all on-board voltages. A large number of configurable I/Os are provided via rugged high-speed board-to-board connectors.

Key Features

• SoC/FPGA
  • Package: CLG484
  • Device: Xilinx Z-7020
  • Speed: -1 *
  • Temperature: C grade *.
• RAM/Storage
  • Low Power DDR3 SDRAM on PS
    • Data width: 32bit
    • Size: def. 1GB *
    • Speed: 1600 Mbps **
  • QSPI boot Flash
    • Data width: 4bit
    • Size: 32MB *
  • MAC address serial EEPROM with EUI-48™ node identity
  • 512Kb user MAC address serial EEPROM.
• On Board
  • 10x 12-Bit Low Power SAR ADCs up to 2 MSPS
  • Low Power Oscillators.
  • Gigabit Ethernet PHY transceiver
  • High-Speed USB 2.0 ULPI transceiver with full OTG support
  • Single chip High-Speed USB 2.0 to UART/JTAG Interface (Xilinx License included) (FTDI FT2232H).
  • 2 x User RGB LEDs (Green), LED FPGA "Done" (Green).
  • 2 x Tactile Switches (User), 1 x Tactile Switche (Reset).
• Interface
  • 120 x HR PL I/Os (3 banks).
  • 2 x PS MIOs (shared with UART TX/RX ZYNQ-FTDI).
  • 1 Gbps RGMII Ethernet interface.
  • High Speed USB 2.0 ULPI with full OTG support.
  • High Speed USB 2.0 to UART/JTAG interface, including microUSB-B connector.
  • microSD
  • JTAG
• Power
  • On-board high-efficiency DC-DC converters for all voltages used.
• Dimension
  • 45 x 65 mm
• Notes
  • * depends on assembly version
  • ** depends on used Zynq and DDR3 combination

Scope of Delivery

• 1 x TE0716-01-61C32-A SoM with Xilinx Zynq-7000 SoC XC7Z020