Products with Xilinx FPGA

Previous Next
Products with Xilinx FPGA

TEI0022｜DataStorm DAQ

TEI0022-DataStorm DAQ｜M-Board FMC Carrier for M-Series Precision Converters

The Trenz Electronic TEI0022 is a SoC board based on Intel Cyclone V FPGA, an Ethernet PHY, one GByte DDR3 SDRAM per HPS and FPGA and one 32 MByte Quad SPI Flash memory for configuration and operation per HPS and FPGA, and powerful switching-mode power supplies for all on-board voltages.

 

Key Features

  • SoC FPGA
    • Intel Cyclone V (5CSEMA5F31C8N)
    • Package: FBGA 896 pins
    • Speed grade: 8
    • FPGA Temperature range: commercial (Tj = 0 °C to 85 °C)
  • RAM/Storage
    • 1 GByte DDR3 SDRAM for HPS
    • 1 GByte DDR3 SDRAM for FPGA
    • 32 MByte SPI for HPS
    • 32 MByte SPI for FPGA
  • On Board
    • Up to 7 x SMA connector
    • Temperature sensor
    • Intel MAX10 for board management
  • Interface
    • LPC FMC connector
    • 4 x Pmod connector
    • JTAG
    • UART via micro USB B connector (for FPGA)
    • UART via micro USB B connector (for HPS)
    • 4 x USB 2.0 host
    • Ethernet via RJ45 connector
    • SD card
    • HDMI
  • Power
    • 12V input supply voltage
  • Dimension: 13 x 16 cm

Scope of Delivery

  • 1 x TEI0022-03 Trenz Electronic SoC module with Intel Cyclone V FPGA
  • 1 x 28169 power Supply with four exchangeable adapters and cable, 12V/2.5A
  • 2 x bolts
  • 4 x screws

規格:

Device list

SDRAM

max

Flash

On Board

Interface

Other Features

Cyclone V 5CSEMA5F31C8N

1 GB for HPS 1 GB for FPGA

32 MB SPI for HPS

32 MB SPI for FPGA

Up to 7 x SMA connector, temperature sensor, Intel MAX 10 for board management

Connectors: LPC FMC, 4 x Pmod, JTAG, UART via microUSB B (for FPGA and HPS), 4 x USB2.0 host, Ethernet, SD card, HDMI

Power: 12V input supply voltage

 

  產品編號：TEI0022-03
  線上商店： 購買連結 可線上刷卡/享運費補助！
Previous Next
Products with Xilinx FPGA

TEB0835｜PCIe Carrier Board

TEB0835－PCIe Carrier Board｜PCIe Baseboard for Trenz Electronic TE0835 RFSoC

The TEB0835 is a carrier for Trenz Electronic's TE0835 module which is based on Xilinx UltraScale+ RFSoC. It is equipped with a microSD card reader, microUSB2.0, 21x UMCC connectors and six SMD connectors for clocks and ADC/DAC inputs/outputs, six green user LEDs, reset push button, DIP switch for mode, battery holder, FT2232H FTDI,  programmable clock generators and a temperature sensor IC. The carrier provides PCIe connector as well.

 

Key Features

Designed for

  • TE0835 RFSoC series

RAM/Storage

  • 4 Kb EEPROM

On Board

  • Programmable clock generator
  • I2C switch IC
  • 6 x user green LEDs
  • 16 x RF transformation
  • Reset push button
  • Temperature sensor
  • FT2232H FTDI
  • SDIO port expander
  • 2 x DIP switch
  • Pin headers
  • PCIe 6 connector

Interface

  • 21 x UMCC connectors
  • 6 x SMA connectors
  • 2 x Micro USB2.0
  • RJ45 LAN socket
  • Micro SD card socket
  • 2 x UEC5 connectors
  • 2 x UCC8 connectors
  • PCIe x8 card
  • 2 x Samtec Razor Beam SS5 (2 x 80 pol) Board to Board connectors

Power

  • 12V input supply voltage

Dimension

  • 10.66 x 16.76 cm

 

Scope of Delivery

  • 1 x TEB0835-02-A Trenz Electronic PCIe Baseboard for Trenz Electronic TE0835 RFSoC

  產品編號：TEB0835-02-A
  線上商店： 購買連結 可線上刷卡/享運費補助！
Previous Next
Products with Xilinx FPGA

TE0722｜Xilinx Z-7007S

TE0722-Z-7007S｜DIPFORTy1 "Soft Propeller" with Xilinx Z-7007S Single-core, 16 MByte Flash

The DIPFORTy1 "Soft Propeller" is based on the Xilinx Zynq-7000S, a System on Chip which contains a FPGA and a Single-core ARM A9+ processor with enough logic gates to become a Propeller. The board also has 16 MByte of Flash used for configuration and everything fits on a Propeller-compatible DIP 40 pinout.

DIPFORTy1 "Soft-Propeller" is the lowest cost Zynq-based module ever made and the first ZYNQ module that can use existing bases and project boards (Parallax Propeller chip compatibility). All this in a compact 1.8 x 5.1 cm form factor, at the most competitive price.

This device contains a single-core ARM Cortex-A9 processor and represents the lowest cost entry point to the scalable Zynq-7000 platform.

 

Key Features

  • Xilinx Zynq-7: XC7Z007S-1CLG225C
    • 16 MByte SPI Flash (primary boot)
    • 33.333 MHz Clock (MEMS Oscillator)
    • Single-core ARM A9+
  • DIP40 form factor
    • 2 x 20 holes for socket pins or pin-header
    • Size: 18 x 51 mm
  • Total user accessible PL I/O: 46 (+3 Input only)
    • DIP40 header pins: 34 I/O
    • XMOD J1: 6 I/O
    • XMOD J2: JTAG + 2 I/O (or 3 input + 2 I/O)
    • XMOD J3: 4 I/O
  • 3.3 V single supply
  • RGB LED (PL I/O connected)
  • "Done" LED (inverted polarity)
  • User LED (ARM CPU MIO GPIO)
  • MicroSD Card socket (MIO, ZYNQ secondary boot media)
  • Sil1143 Proximity and ambient light sensor

Scope of Delivery

  • 1 x TE0722-02-07S-1C Trenz Electronic module with Xiinx Zynq-XC7Z007S
  • 1 x Pinheader, double row, 10-pins, straight
  • 2 x Pinheader, single row, 20-pins, straight

  產品編號：TE0722-02-07S-1C
  線上商店： 購買連結 可線上刷卡/享運費補助！
Previous Next
Products with Xilinx FPGA

TE0722｜ DIPFORTy Soft Propeller Xilinx Zynq-7010

TE0722｜DIPFORTy1 Soft Propeller with Xilinx Zynq-7010 and 16 MByte Flash

The DIPFORTy1 "Soft Propeller" is based on the Xilinx Zynq-7010, a System on Chip which contains a FPGA and a Dual Core ARM A9+ processor with enough logic gates to become a Propeller. The board also has 16 MByte of Flash used for configuration and everything fits on a Propeller-compatible DIP 40 pinout.

DIPFORTy1 "Soft-Propeller" is the lowest cost Zynq-based module ever made and the first ZYNQ module that can use existing bases and project boards (Parallax Propeller chip compatibility). All this in a compact 1.8 x 5.1 cm form factor, at the most competitive price. 

 

Key Features

  • Xilinx Zynq-7 XC7Z010-1CLG225C
    • 16 MByte SPI Flash (primary boot)
    • 33.333 MHz Clock (MEMS Oscillator)
    • Dual Core ARM A9+
  • DIP40 form factor
    • 2 x 20 holes for socket pins or pin-header
    • Size: 18 x 51 mm
  • Total user accessible PL I/O: 46 (+3 Input only)
    • DIP40 header pins: 34 I/O
    • XMOD J1: 6 I/O
    • XMOD J2: JTAG + 2 I/O (or 3 input + 2 I/O)
    • XMOD J3: 4 I/O
  • 3.3 V single supply
  • RGB LED (PL I/O connected)
  • "Done" LED (inverted polarity)
  • User LED (ARM CPU MIO GPIO)
  • MicroSD Card socket (MIO, ZYNQ secondary boot media)
  • Sil1143 Proximity and ambient light sensor

Scope of Delivery

  • 1 x TE0722-02 Trenz Electronic module with Xilinx Zynq-7010
  • 1 x Pinheader, double row, 10-pins, straight
  • 2 x Pinheader, single row, 20-pins, straight

  產品編號：TE0722-02
  線上商店： 購買連結 可線上刷卡/享運費補助！

Page 12 of 12