Other Trenz Electronic Products

Previous Next
Other Trenz Electronic Products

TEBA0841｜Carrier Boards for 4 x 5

TEBA0841－TEBA0841 - Simple base for TE0841 and TE0741

The Trenz Electronic TEBA0841 is a low cost carrier board for testing, evaluation and development purposes of TE0841 and TE0741 FPGA modules. Although this base-board is dedicated to the modules TE0841 and TE0741, it is also compatible with other Trenz Electronic 4 x 5 cm SoMs. The carrier board offers one SFP connector, one Micro USB2 B connector, two 2 x 25-pin headers and one XMOD header to get access to the I/O's and interfaces of FPGA modules. To test and evaluate the Multi-Gigabit transceiver units of the FPGA module, 6 MGT lanes on the carrier board are routed in a loop-back circuit on the B2B connectors.

Key Features

  • 3 x Trenz Electronic 4 x 5 module B2B connectors (Samtec LSHM series)
  • SFP+ connector (enhanced small form-factor pluggable), supports data transmission rates up to 10 Gbit/s
  • Micro USB2 type B connector
  • 4 x 5 SoM programmable by XMOD header
  • Soldering-pads for pin headers for access to SoM's I/O-bank pins, usable as LVDS-pairs
  • Soldering-pads for pin headers for access to further interfaces and I/O's of the SoM
  • 2 x user LEDs routed to I/O-pins of the SoM
  • 4-bit DIP switch for setting module parameters
  • 4 x VCCIO selection jumper to set module's bank voltages

Scope of Delivery

  • 1 x TEBA0841-02 Trenz Electronic carrier board for TE0841, TE0741 and compatible modules
  • 1 x TE0790-03 XMOD FTDI JTAG Adapter - Xilinx compatible (pre-assembled)
    This adapter is not suitable for the supply of basic board + module; a power supply has to be attached seperately.
  • 2 x Pin Header, straight, double row, 50 pins
  • 4 x Jumper

產品編號：TEBA0841-02
 線上商店： 購買連結 可線上刷卡/享運費補助！
Previous Next
Other Trenz Electronic Products

TEBF0808｜Carrier Boards for Custom Modules

TEBF0808－UltraITX+ Baseboard for Trenz Electronic TE080X UltraSOM+

The Trenz Electronic TEBF0808 carrier board is a baseboard for the Xilinx Zynq Ultrascale+ MPSoC modules TE0803, TE0807 and TE0808, which exposes the module's B2B connector pins to accessible connectors and provides a whole range of on-board components to test and evaluate the Zynq UltraScale+ SoMs and for developing purposes. The carrier board has a Mini-ITX form factor making it capable to be fitted into a PC enclosure. On the PC enclosure's rear and front panel, MGT interfaces and connectors are accessible, for the front panel elements there are also Intel-PC compatible headers available. 

Key Features

  • Mini-ITX form factor, PC enclosure compatible
  • ATX-24 power supply connector
  • Optional 12V standard power plug
  • Headers
    • Intel 10-pin HDA audio
    • Intel 9-pin power/reset button, Power-/HD-LED
    • PC-BEEPER
  • On-board power-/reset-switches
  • 2 x configuration 4-bit DIP switches
  • 2 x optional 4-wire PWM fan connectors
  • PCIe slot - one PCIe lane (16 lane connector)
  • CAN FD transceiver (10 Pin IDC connector and 6-pin header)
  • 4 x On-board configuration EEPROMs (1 x Microchip 24LC128-I/ST, 3 x Microchip 24AA025E48T-I/OT)
  • Dual SFP+ connector (2x1 Cage)
  • 1 x DisplayPort (single lane)
  • 1 x SATA connector
  • 2 x USB 3.0 A connector (Superspeed Host Port (Highspeed at USB 2.0))
  • 1 x USB 3.0 on-board connector with two ports
  • FMC HPC slot (FMC_VADJ max. VCCIO)
  • FMC fan
  • Gigabit Ethernet RGMII PHY with RJ45 MagJack
  • All carrier board peripherals' I²C interfaces muxed to MPSoC's I²C interface
  • Quad programmable PLL clock generator
  • 2 x SMA coaxial connectors for clock signals
  • MicroSD/MMC card socket (bootable)
  • 32 GBit (4 GByte) on-board eMMC Flash (8 banks a 4 GBit)
  • 2 x System controller CPLDs Lattice MachXO2 1200 HC
  • 1 x Samtec FireFly (4 GT lanes bidirectional)
  • 1 x Samtec FireFly connector for reverse loopback
  • 20-pin ARM JTAG connector (PS JTAG0)
  • 3 x Pmod connector (GPIO's and I²C interface to SC CPLDs and MPSoC module)
  • On-board DC-DC PowerSoCs
  • Size: 170 mm × 170 mm. Please download the assembly diagram for exact details.
  • Mating height with standard connectors: 5 mm

Scope of Delivery

  • 1 x TEBF0808-04A UltraITX+ base board for Trenz Electronic's TE080x series MPSoCs

產品編號：TEBF0808-04A
 線上商店： 購買連結 可線上刷卡/享運費補助！
Previous Next
Other Trenz Electronic Products

TEB0729｜Carrier Boards for Custom Modules

TEB0729－Carrier board for TE0729 Zynq-7020 SoC with USB-A-Host Connector

The Trenz Electronic TEB0729 carrier board was especially designed and developed for the use of Trenz Electronic module TE0729. It provides low-cost connection and extension to Trenz Electronic micromodules from the TE0729 series.

Features

  • Barrel jack for 5V power supply
  • 2 x RJ45 10/100-BaseT Ethernet MagJack with 2 integrated LEDs
  • 1 x RJ45 Gigabit Ethernet MagJack with 2 integrated LEDs.
  • 2 x Configuration EEPROM's, connected to SoM's I²C interface
  • XMOD compatible header to connect the TE0790 USB 2.0 adapter board
  • JTAG and UART interface over XMOD header
  • MicroSD Card socket, can be used to boot system
  • USB 2.0 socket
  • 4-bit DIP switch for SoM configuration (SoM's JTAG access and Bootmode)
  • VG96 connector soldering-pads J8 for access to SoM's PL-IO-bank-pins, usable as LVDS-pairs
  • VG96 connector soldering-pads J9 for access to further interfaces and IO's of the SoM
  • 1 x user LED (red)
  • 1 x user push-button routed to SoM (Reset function at standard configuration)
  • Pin headers to set PL-IO-bank's VCCIO with jumper

Scope of Delivery

  • 1 x TEB0729-03A Trenz Electronic carrier board for TE0729 SoC Module
  • 2 x VG96 Socket Connector Vertical

產品編號：TEB0729-03A
 線上商店： 購買連結 可線上刷卡/享運費補助！
Previous Next
Other Trenz Electronic Products

TEB0728｜Carrier Boards for Custom Modules

TEB0728－Carrierboard for a TE0728 Automotive Zynq-7020 SoC Module

The Trenz Electronic TEB0728 carrier board provides low-cost connection and extension to the Trenz Electronic TE0728 micromodule.

Features

  • Trenz TE0728 Module Socket (3 x Samtec connectors, 80 Pins)
  • 2 x RJ45 Ethernet
  • SD card connector
  • Board supply via DC-Jack
  • Red/yellow/green triple LED
  • 1 x User Push Button

Scope of Delivery

  • 1 x TEB0728-02 Trenz Electronic carrier board for the TE0728
  • 2 x VG96 Socket Connector Vertical

產品編號：TEB0728-02
 線上商店： 購買連結 可線上刷卡/享運費補助！
Previous Next
Other Trenz Electronic Products

TEB0745｜Carrier Boards for Custom Modules (2)

TEB0745－Carrierboard for a TE0745

The carrier board TEB0745 was especially designed and developed for the use of Trenz Electronic module TE0745. You can find further informations in our download-area.

Key Features

  • Form factor 20 cm x 23.1 cm
  • Trenz TE0745 Module Socket (3 x Samtec connectors)
  • 24 V power supply over ARKZ950/2 connecting terminal
  • 1 x EMI Network Filter
  • 3 x Variable Step Down Regulator Module (VDRM) with head sink
  • 2 x Synchronous Buck Regulator
  • 1 x XMOD (TE0790) Pin Header (JTAG / UART)
  • 1 x TE0790 XMOD FTDI JTAG Adapter - Xilinx compatible (pre-assembled)
  • 1 x Pin Header (JTAG)
  • 1 x microSD connector
  • 1 x RJ45 Ethernet connector
  • 1 x USB Host Connector
  • 8 x SFP-Connector
  • 6 x Pin Header 50 pol. (FPGA Bank I/O's and Power)
  • 6 x Pin Header 12 pol. (FPGA Bank I/O's and Power)
  • 1 x battery holder
  • 2 x DIP Switch Array (VCC_HR_B / Modi)
  • 2 x Button (User / Reset)
  • 2 x LED (Green)

Scope of Delivery

  • 1 x TEB0745-02 Trenz Electronic carrier board for TE0745
  • 1 x TE0790 XMOD FTDI JTAG Adapter - Xilinx compatible (pre-assembled)

產品編號：TEB0745-02
 線上商店： 購買連結 可線上刷卡/享運費補助！
  1. TEBA0714｜Carrier Boards for Custom Modules (3)

第 2 頁，共 3 頁