TE0701－Carrier Board for Trenz Electronic 4 x 5 Modules

The Trenz Electronic TE0701 Carrier Board is a base-board for 4 x 5 SoMs, which exposes the module's B2B-connector-pins to accessible connectors and provides a whole range of on-board components to test and evaluate TE 4 x 5 SoMs.

Key Features

• Trenz 4 x 5 Module socket (3 x Samtec LSHM connectors)
• RJ45 GbE Ethernet
• MicroUSB connector (Device, Host or OTG modes)
• SD Card connector - Zynq SDIO0 bootable SD port
• Pmod connector A, 3.3V
  • 6 Pins can be multiplexed to SD Card pins (MIO1 bank when using TE0720)
  • 2 Pins connected to carrier controller CPLD
• Pmod connector B, 3.3V
  • Mapped to 8 PS MIO0 pins if using TE0720 (same mapping as on zedboard)
  • 6 pins also connected to carrier controller CPLD
• Single 12V power supply
• High performance Enpirion DCDC converter for local supplies
• VITA57.1 compliant FMC LPC connector
  • Digitally programmable FMC VADJ power supply
• Carrier controller CPLD
  • 1200 Macrocell CPLD with Block RAM, Flash and PLL
  • 8 user LEDs mappable to different functions
  • 2 user pushbuttons mappable to different functions
  • VID and EN control for FMC VADJ DCDC regulator
• USB JTAG interface
  • Mini USB connector
  • Compatible with Xilinx tools: Impact, Chipscope, XMD, Vivado/SDK etc.
  • Compatible with OpenOCD debugger including ZYNQ SRST control
  • Based on FT2232H USB chip
  • Channel A can toggle module (Zynq PS) reset
  • Channel B can be used as USB UART
    • Carrier controller can reroute RXD/TXD signals
  • JTAG port can be connected to (by the carrier controller)
    • 4 x 5 module JTAG (FPGA + ARM chained in Zynq)
    • 4 x 5 module JTAG and FMC JTAG in chain
    • FMC JTAG alone
    • Zynq ARM PS JTAG port (via EMIO muxing in TE0720)
    • 6 pin header for off board use
    • Pmod connector B for off-board use

Scope of Delivery

• 1 x TE0701-06 carrier board for Trenz Electronic modules with 4 x 5 cm standard footprint only

TE0705 - Simplified carrier board based upon TE0701

The baseboard TE0705 is a "downgraded" version from TE0701 and it provides low-cost connection and extension to Trenz Electronic modules with a standard footprint of 4 x 5 cm.

As little as possible has been changed in functionality (except the functionality that was removed).

Key Features

• Trenz 4 x 5 module socket (3 x Samtec LSHM connectors)
• RJ45 GbE Ethernet
• Micro USB connector (Device, Host or OTG modes)
• SD Card connector
• High performance DCDC converter for local supplies
• Carrier controller Lattice MachXO2 CPLD
  • 1200 Macrocell CPLD with Block RAM, Flash and PLL
  • 8 User LEDs mappable to different functions
  • 2 User Pushbuttons mappable to different functions
  • 80 I/O's
• USB JTAG interface
  • Mini USB connector
  • Compatible with Xilinx tools
  • Based on FT2232H USB chip

Scope of Delivery

• 1 x TE0705-04 carrier board for Trenz Electronic modules with 4 x 5 cm footprint
• 1 x Mini-Fit JR Receptacle 2Pol.
• 4 x Mini-Fit Female Crimp Terminal 18-24 AWG

Use with TE0715-xx-30-xx
For use with TE0715-xx-30-xx or any other 4 x 5 module that has some banks without 3.3V tolerance the I/O voltage must be changed by moving the jumper J21 to position "VADJ".It may be requried to update the CPLD on TE0705 first.

TE0703 - Carrier board for Trenz Electronic modules with 4 x 5 cm form factor

The Trenz Electronic TE0703 carrier board is a baseboard for 4 x 5 SoMs, which exposes the MIO- and the PS/PL-pins of the SoM to accessible connectors and provides a whole range of on-board-components to test and evaluate Trenz Electronic 4 x 5 SoMs.

Key Features

• Trenz 4 x 5 module socket (3 x Samtec LSHM series connectors)
• Two VG96 backplane connectors are not soldered to the board, but they are included in the package as separate components.
• SDIO port expander with voltage-level translation
• Micro SD card connector - Zynq SDIO0 bootable SD port
• 4 x User LEDs
  • D1 and D2 are connected to the carrier controller, their function depends on the firmware
  • D3 and D4 are connected to the 4 x 5 module B2B connector pins, and are directly controlled by the module
• Mini USB connector (USB JTAG and UART interface)
• 1 x User push button
  • Connected to "intelligent Carrier Controller (iCC)" and can be used as module reset button. Other usage possible, actual function depend on the code loaded into iCC.
• RJ45 GbE connector
• USB host connector
• Barrel jack for 5 V* power supply
• 4A high efficiency power SoC DC-DC step-down converter with integrated inductor for 3.3 V power supply
• USB JTAG and UART interface (FTDI FT2232H), compatible with Xilinx tools (also with many other tools)
• 4 User DIP switches
  • Enable/disable update of the "intelligent Carrier Controller"
  • MIO0 (readable signal by iCC and module)
  • 2 "mode" bits

Scope of Delivery

• 1 x TE0703-06 carrier board for Trenz Electronic modules with a form factor of 4 x 5 cm
• 2 x VG96 socket connector vertical (DIN 41612), female, series 0903, manufacturer part no. 09032967824

TE0706 - Carrierboard for Trenz Electronic Modules with 4 x 5 cm Form Factor

The TE0706 carrier board provides functionalities for testing, evaluation and development purposes of Trenz Electronic 4 x 5 cm SoMs. It is mainly for the use with TE0720 and TE0715 modules. The carrier board is equipped with various components and connectors for different configuration setups and needs. The interfaces of the SoMs functional units and PL I/O-banks are connected via board-to-board connectors to the carrier board's components and connectors for easy user access.

Key Features

• 3 x Samtec LSHM series board to board connectors
• VG96 connector (mounting holes and solder pads) and 50-pin IDC male connector socket for access to PL I/O-bank pins
• USB2.0 type A connector, or optionally Micro USB 2.0 connector
• 1 x RJ45 GbE MagJack, connected via MDI to B2B connector
• 1 x GbE PHY, providing Ethernet interface in conjunction with RJ45 GbE MagJack
• 4A High-Efficiency Power SoC DC-DC Step-Down Converter for 3.3V power supply
• XMOD JTAG-/UART-header JX1
• 1 x TE0790, XMOD FTDI JTAG Adapter - Xilinx compatible (pre-assembled)
• Micro SD card socket
• SDIO port expander with voltage-level translation and jumper for selection of SDIO voltage on SoM side
• DIP-switches S1 to set SoM's control signals
• 1 x user-push button, by default configured as system reset button
• 3 x VCCIO selection jumper to set SoM's PL I/O-bank voltages
• 5V power supply barrel jack
• Size: 64.5 x 100 mm

Scope of Delivery

• 1 x TE0706-03 carrier board for Trenz Electronic modules with a form factor 4 x 5 cm
• 1 x TE0790-03, XMOD FTDI JTAG Adapter - Xilinx compatible (pre-assembled)
• 1 x VG96 socket connector vertical (DIN 41612), female, series 0903, manufacturer part no. 09032966825