Products with Lattice FPGA

Previous Next
Products with Lattice FPGA

CR00103 ｜Lattice Certus-NX

CR00103－CRUVI Certus-NX Base Board with Lattice Certus-NX FPGA, 8 MB RAM, 4.5 x 5.7 cm

This board based on the Nexus FPGA Certus-NX from Lattice and designed according to the new CRUVI standard．

Key Features

  • On Board
    • Certus NX LFD2NX-40-7BG196I FPGA
    • FTDI (JTAG and UART over micro USB connector)
    • 3 x LEDs (1 x power indicator, 2 x user)
    • 2 x user push buttons
  • RAM/Storage
    • EEPROM
    • 8 MB HyperRAM
    • 16 MB QSPI Flash Memory
  • Interface
    • Micro USB 2.0
    •  CRUVI
      • 2 x 34 pin connector
      • 1 x high speed 60 pin connector
      • 1 x low speed 12 pin connector
  • Power
    • micro USB connector or 2 x 34 pin connector
  •  Dimension
    • 57,5 mm x 44,85 mm

Scope of Delivery

  • 1 x CR00103-02-A Trenz Electronic CRUVI Certus-NX Base Board with Lattice Certus-NX FPGA
  • 4 x screws

產品編號：CR00103-02-A
 線上商店：購買連結 可線上刷卡/享運費補助！

Previous Next
Products with Lattice FPGA

TEL0001 Series｜LXO2000｜Lattice XO2

TEL0001 Series－LXO2000 with Lattice XO2-4000, On-Board USB/JTAG, 2.5 x 6.15 cm

The TEL0001 "LXO2000" is a low cost FPGA module integrating a Lattice XO2-4000 and on-board USB/JTAG. It's compatible to the Arduino MKR standard.

 

 

Key Features

  • Lattice LCMXO2-4000HC-4QN84C FPGA
  • Form factor 2.5 x 6.15 cm
  • On-board USB/JTAG
  • On-board USB/serial
  • Total I/O
    • 22 I/O on MKR header
    • Optional Pmod header (8 I/O)
  • 2 push buttons
  • 8 LEDs
  • 100 MHz MEMS oscillator
  • Supply: USB or 5 V from pin header

Scope of Delivery

  • 1 x TE0001-02 Trenz Electronic FPGA module with Lattice XO2-4000

產品編號：TEL0001-02
 線上商店： 購買連結 可線上刷卡/享運費補助！
Previous Next
Products with Lattice FPGA

TE0876 Series｜IceZero｜Lattice ICE40

TE0876 Series－IceZero with Lattice ICE40HX, 4 Mbit external SRAM, 3.05 x 6.5 cm

The IceZero is a low cost general purpose Lattice FPGA platform for the Raspberry Pi. It includes 4 Mbit of external SRAM and 4 2x6 Pmod interfaces for 32 3.3V LVCMOS IO's to external expansion devices. The board is powered and configured over the standard 2x20 Raspberry Pi header. The ICE40HX4K FPGA is fully supported by Clifford Wolf’s "icoTC" Project IceStorm tool chain.

Example designs (both Verilog and Python) for the SUMP2 Logic Analyzer and general purpose GPIO (inputs, outputs, PWM servo control, etc.) are available from the Black Mesa Labs website. Mesa Bus Protocol virtual PCI 32bit communication between FPGA and Pi is supported over the Pi's 32 MHz SPI serial interface. Black Mesa Labs strives to provide multiple free open-source example designs for the IceZero platform for expanding RaspberryPi hardware interface capabilities -bitstream complete- no FPGA design experience required.

 

 

Key Features

  • FPGA: Lattice iCE (iCE40HX)
  • Size: 30.5 x 65 mm
  • Supported by fully open source FPGA toolchain (icoTC)
  • Full FPGA design flow on Rasperry Pi (all open source)
  • Fast FPGA configuration from Rasperry Pi
  • Raspberry Pi HAT Compatible
  • Compatible in size with Raspberry PiZero and PiZero-W
  • 4 Mbit external SRAM
  • User LED: 3
  • SPI Flash for FPGA self-configuration
  • User Clock: 100 MHz
  • Pmod connectors: 4 (not assembled by default)

Scope of Delivery

  • 1 x TE0876-02-A Trenz Electronic IceZero module with Lattice iCE40HX

產品編號：TE0876-02-A
 線上商店： 購買連結 可線上刷卡/享運費補助！