CR00100-CRUVI MAX 10 Base Board with Intel MAX 10 FPGA, 8 MByte SDRAM, 4.5 x 5.7 cm

The Trenz Electronic CR00100-01 is a CRUVI base board with Intel FPGA.

Key Features

• On Board
  • JTAG and UART over Micro USB connector
  • 2 x User Push button
  • 4 x User LEDs (red, green)

• SoC/FPGA
  • Intel MAX10 FPGA (10M08 as standard option)

• RAM/Storage
  • 8 MByte SDRAM

• Interface
  • 1 x CRUVI LS
  • 1 x CRUVI HS

• Power
  • Power from micro USB connector

• Dimension
  • 44.86 mm x 57.50 mm

Scope of Delivery

• 1 x CR00100-01-DBC82A Trenz Electronic CRUVI MAX10 Base Board with Intel MAX 10 FPGA
• 4 x screws

TEI0003 Series－CYC1000 with Cyclone 10 FPGA, 8 MByte SDRAM

The Trenz Electronic TEI0003-02 is a small and powerful FPGA module integrating an Intel Cyclone 10 LP FPGA, 8 MByte SDRAM, 2 MByte Flash and a LIS3DH 3-axis sensor.

Key Features

• Intel Cyclone 10 LP FPGA:
  25 kLE, 66 Memory blocks (9K), 594 Memory blocks (Kb), 18 x 18 multipliers -> 66
• 8 MByte SDRAM
• 2 MByte Flash (EPCQ16A)
• LIS3DH 3-axis Sensor
• 21 I/O Arduino MKR compatible headers
• Pmod: 2x6 Pin support
• 8 x user LEDs
• 1 x user push button
• 5.0 V single power supply with on-board voltage regulators

Default assembly variant: 10CL025 with 25kLE

Possible variants: 10CL006, 10CL010, 10CL016

Scope of Delivery

• 1 x TEI0003-02 Trenz Electronic FPGA module with Intel Cyclone 10 LP FPGA
• User manual

TEI0001 Series-Arduino MKR Standard 2.5 x 6.15 cm

The new FPGA IoT Maker Board that has been designed for end-to-end application development and optimised for cost. The Arrow MAX1000 board can be installed directly into a custom application or integrated on to a completely separate board. It has been created for start-ups, universities or established equipment manufacturers who want a flexible, low cost FPGA platform for development. Also customised variants can be supplied.

At the heart of the maker board is a compact (11x11mm) Intel MAX 10 FPGA with 8000 logic elements. This single chip includes integrated flash memory, a 1Msps 12bit ADC for analogue signals and a 3.3V power supply. Other features include embedded SRAM, DSP blocks, instant-on within milliseconds, and the ability to implement Intel’s NIOS II soft core embedded processor to perform microcontroller tasks.

The MAX1000’s power can be supplied as 5V from the USB port or via a separate pin. An Enpirion DC/DC converter with integrated coil then generates the 3.3V supply used on board. A MEMS oscillator provides the clock supply for the FPGA and the USB bridge. The low power, 3-axis acceleration sensor – also based on MEMS technology – can be used for position and motion detection, which are often required in IoT applications. External SDRAM can be used for storage of application data or as memory for the NIOS II processor.

To provide an easy introduction into the use of FPGAs, a series of demo projects with NIOS II soft IP controllers are provided with the MAX1000. Eight configurable LEDs are available to display status and user inputs can be made via two buttons. A two row connector, based on the Arduino MKR standard, and a Pmod plug provide flexible connectivity options including the ability to attach adaptor boards for wireless ICs or sensors.

Key Features

Scope of Delivery

• 1 x TEI0001-03-16-C8A Trenz Electronic FPGA module with Intel MAX 10, 16 kLE
• User manual

TEF0008 Series－FMC Card with four SFP+ 10 Gbit ports

The Trenz Electronic TEF0008 is a FPGA to Mezzanine Card (FMC) based on VITA 57.1 FMC HPC Standard, with four SFP+ 10 Gbit ports for fiber optical SFP modules. It is inteded for use on a FMC HPC carrier and can not be used stand-alone.

The front panel included in the scope of delivery is used for mounting the TEF0008 on one of our PCIe cards.

Mounting holes near the front pannel are not implemented due to physical restrictions caused by the SFP cage. The dimensions exceed in some area the by Vita 57.1 standard defined dimensions. In the middle region of the card the cage is higher than the specified max high for this area. Check carefully if the carrier card uses this space for other components conflicting mechanical. The bottom side is at the high limit.

Key Features

• Four SFP+ 10 Gbit ports
• HPC FMC connector
• Low jitter programmable clock generator
• Intel MAX10 FPGA 10M08SAU169C8G
• 3.3 V to 1.8 V DC/DC converter
• 128 Kbit EEPROM
• Status LED (green)
• Dimension: 69 x 84 mm, SFP+ connector excluded (+ 5.5 mm)
• Highest part on PCB top is 9.5 mm (SFP+ cage, excluded front plate), bottom 1.4 mm (MAX10 FPGA)

Scope of Delivery

• 1 x TEF0008-02 Trenz Electronic FMC card
• 1 x FPF0008-01 front panel for mounting TEF0008 on PCIe card
• 2 x screws